Item Tag 6 Pack

1 set of replacement filters with following : (1-6) x Cation Resin Cartridge Filter Size 9 7/8 inch x 2.5 inch - Fits most standard 10 inch size housings and most reverse osmosis systems.Filter Media: Cation Resin Capacity : 750 grains Maximum Recommended Flow Rate: 2.5 to 5 GPM (depends on incoming water pressure). Operational Temperature Range: 40°F to 100°F Maximum pressure: 125 PSI (8.6 bar) Minimum pressure: 20 PSI (1.4 bar) 5-Micron nominal rating. Cartridge capacity dimensions - ID: 30mm OD: 70mm Reduces Total Dissolved Solids (TDS) and hardness, can also be used as a pre-filter to prevent build-up of scale on sensitive equipment. End Caps: Polypropylene Inner/Outer Wraps: Polyolefin Netting: Polyethylene All filters are individually wrapped. Detailed Description For water hardness reduction, our Cation Resin Filter softens your water by releasing Hydrogen (H+) ions or other positively charged ions in exchange for impurities present in the water. The process involves passing water containing hardness mineral ions, namely calcium (Ca2+) and magnesium (Mg2+) through a column containing a strongly cation exchange resin in the sodium (Na+) form (i.e. the exchangeable cations are sodium). The calcium and magnesium ions are exchanged for an equivalent number of sodium ions. The resin, once exhausted, (i.e. all the available sodium ions have been exchanged) must be re-charged. This entails passing a solution containing a high concentration of sodium salts, such as brine (sodium chloride), through the ion exchange resin in a process known as regeneration. 1 x Pleated Sediment Filter Size 9 7/8" x 2.5" - Fits most standard 10" size housings and most reverse osmosis systems.Pleated Polypropylene Sediment Filter 5 micron Used to Remove small particles & suspended matter such as silt, rust, sand, algae, sediment, scale particles from water. Meets FDA requirements for food and beverage contact. Washable filter to help minimize the filtration cost. Operation Temperature: 40°F to 140°F. Low surface area, lower pressure drop. --> 1 x GAC 10" Coconut shell Carbon Filter Size 9 7/8" x 2.5" - Fits most standard 10" size housings and most reverse osmosis systems. Remove Chlorine, Turbidity, Bad Taste & Odor, Sediment, Dirt, and THMS from water. Thick Wall Coconut Base Carbon Filter Media - 100% coconut shell carbon Designed For maximum contact between the water and carbon. 1 Micron filter membrane included to prevent carbon fines to pass from the filter to your drinking water. Operation Temperature: 40°F to 125°F 1 x CTO Carbon Block Filter Size 9 7/8" x 2.5" Fits most standard 10" size housings and most reverse osmosis systems. Remove small particles and carbon fines may pass from second stage & to ensure 100% of chlorine removal from water. 1 x Standard Inline Carbon Cartridges Dimensions: 2" x 10" - Fits standard Reverse Osmosis Systems - 10 Micron Nominal Removes Chlorine , Bad Taste & Odor ,Turbidity ,Sediment ,THMs and Dirt. Helps to polish the taste of reverse osmosis water (Last Stage), Ice maker Refrigerators Drinking Coolers Max Flow: 0.5 GPM Max Pressure: 125 PSI Max Temperature: 100°F Inlet/Outlet: 1/4" NPTF thread (fitting is required) 1 X Reverse Osmosis Membrane NSF Certified. 50 GPD R.O. Membrane at 60 PSI We Suggest to change your membrane every 2 year To remove particles down to 1/10,000 of a micron ( which is 98% of impurities including Organic, inorganic And chemicals). --> 1 X Inline Mineral/Infrared/Alkaline Cartridge Dimensions: 2" x 10" - Fits all Reverse Osmosis Systems. Filter Service Life 1500 Gallons (5676 Liter) Max Flow: 0.75 GPM Max Pressure: 125 PSI (8.6 Bar) Max Temperature: 100°F Inlet/Outlet: 1/4" NPT --> 1 X Inline Remineralization Cartridge Dimensions: 2" x 10" - Fits all Reverse Osmosis Systems Filter Service Life: 1500 Gallons ( 5676 Liter) Max Flow: 0.75 GPM Max Pressure: 125 PSI (8.6 Bar) Max Temperature: 100°F Inlet/Outlet: 1/4" NPT --> Total 1-6 filter(s) individually wrapped. --> --> --> --> --> --> -->